Here are 8 easy steps to jump start your diesel truck with 2 batteries. We have added all the required tools in this detailed guide.
How to jump start a diesel truck with 2 batteries? You can jump start a diesel truck with 2 batteries by bringing both vehicles closer, locate the batteries, turn off the engine, attach positive and negative terminals, start the trucks, and disconnect the jumper cables.
The diesel truck shows maximum performance with two batteries. Usually, these have two batteries.
These batteries provide cranking power to overcome the engine’s resistance and heat the fuel in the engine.
How to jump start a diesel truck with 2 batteries?
In this article, we have added proven methods to jump-start your pickup. You can easily do this yourself, however, it is recommended you take help from a friend.
Tools required
- Jumper leads
- Clamps
- Wire brush
- Gloves
- Glasses
- Donor truck
Line up vehicles
You can choose any park or any less populated area. It can prevent any injury or accidents. The positioning of both vehicles is essential.
You should park them close to each other. It is necessary so that both automobiles get connected through these leads.
When the leads are short, then minimize the distance between them. Be careful; both vehicles should not touch each other. It can produce sparking and flames.
Another critical point is how pickups should face each other. It depends upon the position of the products and their size.
Most pickups have devices on their sides, then park them side by side. When these are fitted on the engine’s top, park them as they are facing each other’s front side.
Locate the batteries
It is a tricky part to perform because different automobiles have their gadgets located at different positions. You should always choose high-quality battery for your truck.
To confirm the exact location of it, you should read the manual of both trucks. After finding out the position, open the hood, and support it with some supporting tool present in the device and the engine.
These are usually hidden inside the hoods. Wear gloves and safety jackets before touching any part. It is necessary to follow all the precautionary measures to protect us.
Then locate both positive and negative terminals, different brands use different codes to mark the positive and negative terminal.
Some have a red and black color on the terminals to distinguish them, few also use + and _ sign to express them.
Carefully look for these signs. Then clean off all the dirt and filth from them by using a brush or clean cloth. If your camper fridge is not cold, this can be the possible cause.
Turn off the engine
Turn off the engine of both the vehicles and remove the keys from the ignition.
Then turn off the light heater and any other accessories attached to the power supply. It is essential because the engine can get a charge from the terminals and flame up the fire.
After turning off all the things, check the battery of the donor vehicle. It should have a maximum charge to transfer to your pickup.
When the donor truck is also low, then all your efforts will go in vain. So first, confirm the condition of both devices.
You can also look for some other donor vehicle if this one does not have enough capacity to donate.
Attach positive and negative terminal
To attach the terminals, you should have the required cables, these are used to connect the donor battery to the dead battery.
You should buy cables with thick cables and heavy clamps. These cables should have an average gauge of 5.
It should have enough length to connect both products. These wires have different colors that differentia the positive and negative sides.
Now take the cables and keep the positive and negative clamps away. They should not touch each other.
First, attach one side of the cable to the donor truck’s positive terminal and then connect the other clamp to the positive terminal.
Always attach the positive terminals first and then attach negative terminals. When you are sure that positive clamps are tightly connected, take the negative clamps.
Start the donor truck
Before pressing the ignition, wait for 2 to 3 minutes. Now start the donor vehicle by turning on its engine.
Let it charge for 4 to 5 minutes. It s timing depends upon how long the battery is dead and the condition of the devices.
When the product is new and functioning correctly, it will only take a few minutes. Old products take a longer time to get charged, never rush into this procedure.
Start the diesel truck
Turn on the engine and see it is working. If it is not working, give some additional time for charging.
Also, try to revive the engine of the donor truck during charging. It can help a lot in turning on the engine. Wait until the engine starts working. When it starts, keep it running for approximately 15 to 20 minutes.
When the engine is still causing a problem in turning on, then recheck the connections of clamps.
When the ignition turns the lights on, and the engine starts making sound without functioning, there must be a problem. When you are continuously failing in the attempt, you should check the equipment and check its condition.
Disconnect the jumper cables
When you are sure about the functioning of the automobile, then remove the connections. First of all, remove the negative terminal clamp from the donor and then from the recipient.
Remove the positive clamp from the donor and then from the pickup. You should correctly follow the order of removing the cables.
When removing, keep them away as they can give you a shock during handling.
Now take your vehicle for a drive and drive it continuously for 10 to 20 minutes. Shutting it off after removing cables can make it dead again.
Driving the vehicle gives it power and charge for its maximum functionality.
Things to consider
It is a tricky process, and you should follow all the precautions and tips before starting it.
Before the process, observe the products thoroughly if they are leaking or damaged, then stop experimenting with it. Do not touch the devices and the wires while connecting them.
When you are using some products, check the material of them, In case the able is torn, or its wires are bare, do not use them.
When it gets hot during working, immediately disconnect them. In case you are in an extreme environment, then use thick insulation materials. If your truck battery is draining fast, it can be because of extreme cold or heat.
The engine’s fuel produces many flammable gases and is flammable, so do not smoke during the process. Keep the children away from it. Wear safety goggles and safety dress to protect yourself. Remove all the jewelry from the hands and arms.
Disconnect the wires after turning off both engines. Never remove them when the engines are functioning. It can give you an electric shock. You can adjust the door if it is not opening, and also fix a pickup door that won’t close.
Do not jump-start a frozen battery; it can explode during the process. Observe the battery sides if you see any side bulging out, it means it is frozen, this is a must to prevent any accident or damage to your equipment.
Keep the heater on in the pickup; it will protect the vehicle’s electrical system if there is an overflow of voltage from the donor vehicle.
Related Articles: